TIPS & TRICKS TO FIX A BENT GARAGE DOOR PANEL
Sometimes, a garage door might not close properly or open properly if it is bent. As the garage door moves up and down, a bent panel can get tucked. You can cause a bend in your garage door by running your car through it. Even the smallest of bends can have serious consequences. It is important to repair a bent garage door panel as soon as possible. A small dent may affect the door’s function. For large bends in garage door panels, the same is true.
How do you fix a bent garage door panel? Is it possible to fix a bent garage panel? What can be done to fix a bent garage panel? What is the cost to repair a bent garage door panel Peoria AZ? Continue reading to learn the answers to these questions.
CAN A BENT GARAGE DOOR PANEL BE FIXED?
The door should move up and down normally without difficulty. Sometimes the panel may bend and cause it to lag in operation. This is a common problem many homeowners don’t think about. A small bend in the garage door’s track or rail could be the reason it isn’t working properly. If the garage door bends, the track and rail can also be damaged.
Panels can be broken at the top, bottom, or middle. The door will sag in all cases. You must pay close attention to the panels in order to fix the problem quickly. If you leave the problem unattended, it will only make the problem worse and cause damage to other parts of your garage door. It is important to inspect the panel immediately after you notice a dent. To ensure that the springs are not strained, make sure to check them.
A garage door panel can be repaired, which is a good thing. It must be done correctly. While you can fix a bent garage door panel yourself, even the smallest slip can cause serious injury. It is better to get it checked by a professional.
HOW TO FIX A GARAGE DOOR PANEL WITH BENT?
As we have said, it is better for a professional to fix a bent garage door panel. Here’s how to fix a bent garage panel. Each option can be a great solution.
1. GET A BRAND-NEW PANEL
The best option is to replace the panel. It is not recommended to keep bent panels as this will only make the problem worse. It is much easier to replace damaged panels than to fix them.
To assess the extent of damage, consult an expert. Most garage doors can be replaced within a matter of hours. Your garage door will look brand new once again. A replacement panel is an option for bent garage doors. Replacements are available for panel dents at the top, center, and bottom.
2. GET RID OF THE BEND USING A HAMMER
If A small dent can be easily fixed by using a hammer. To straighten the dent, use a hammer. A wooden mallet can be used to straighten a small bend on the garage door panel. The mallet should be placed behind the part you are trying to straighten. Next, use the hammer gently to hit the part with a dent.
As you hammer the dent, make sure not to injure any fingers. Don’t use too much force to make the dent larger. You should pay more attention to bends in the top panel. You will need to climb up a ladder in order to reach the top.
A temporary solution is to use a hammer to fix the dent. The crack may get worse if you apply too much force. Even if the dent is removed, the area has already been weakened so another bend will most likely occur at that location.
3. USE SUCTION CUPS
Suction cups are another option for fixing a bent garage door panel. Experts are now using this method. This works well for small dents. Suction tools may not work if the door is entirely made of metal.
The suction tool is placed on the dented area and pressure is applied to straighten the damaged section. This only works for small dents. It would not work if your car hits the garage door panel. This method has a few benefits.
4. USE HEAT TO REMOVE THE DENT
It is possible to heat a piece of metal and then cool it. This allows it to return to its original form. If you have metallic panels you can heat them and then let them cool down in a straight line. This will allow you to get rid of the dent. Aluminum foil is required to achieve this.
The aluminum foil should be placed on the section that needs straightening. Next, heat the panel quickly with compressed air and heat. It should only take a few seconds. The panel will then be straightened again.
